Outils pour utilisateurs
Contrôleurs PWM
Différences
Ci-dessous, les différences entre deux révisions de la page.
| Les deux révisions précédentesRévision précédenteProchaine révision | Révision précédente | ||
| documentation:electronique:modules_kits:controleurs_pwm:index [2020/02/22 23:22] – f1sls | documentation:electronique:modules_kits:controleurs_pwm:index [2024/05/14 12:40] (Version actuelle) – [12V~36V @ « 5A »] f1sls | ||
|---|---|---|---|
| Ligne 1: | Ligne 1: | ||
| ====== Contrôleurs PWM ====== | ====== Contrôleurs PWM ====== | ||
| + | |||
| + | ===== 4.5V~36V @ « 5A »===== | ||
| + | {{: | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | * Working voltage : DC4.5V-35V | ||
| + | * Output current: 0-5A | ||
| + | * Output power: 90W (maximum) | ||
| + | * Quiescent current: 7µA (standby state) | ||
| + | * PWM duty cycle: 1%-100% | ||
| + | * PWM frequency: 20khz | ||
| + | * Size: length 30MMx width 26MM (without handle) x height 14MM | ||
| + | * Weight: 0.013KG | ||
| + | * Precautions: | ||
| + | * The DC motor governor input is DC, and it can't be directly connected to AC (for example: household 220V AC), otherwise it will burn out! ! ! | ||
| + | * Do not reverse the positive and negative terminals of the DC power supply, otherwise the governor may be damaged. | ||
| + | * The motor can be positive or negative. When the running direction is inconsistent with the expectation, | ||
| + | * Adjusting the potentiometer knob changes the governor output duty cycle and the motor speed changes. | ||
| + | |||
| ===== 12V~36V @ 3A===== | ===== 12V~36V @ 3A===== | ||
| {{: | {{: | ||
| + | \\ | ||
| + | {{: | ||
| \\ | \\ | ||
| * Input voltage: DC12V - 36V | * Input voltage: DC12V - 36V | ||
| Ligne 23: | Ligne 51: | ||
| ===== 6V~60V @ 30A===== | ===== 6V~60V @ 30A===== | ||
| - | {{: | + | {{: |
| \\ | \\ | ||
| - | * VCC positive supply 10-60V, be sure to set before energizing voltage adaptation | + | * Input Voltage: DC6V-60V |
| - | * GND Negative , if you want to reduce the external interference shielding box connected to terminals | + | * Output Voltage: Linear with load(voltage drop at motor 2 terminals |
| - | * M+ Motor positive | + | * Output Current: 0A-30A |
| - | * M- motor negative | + | * Continuous Current: <20A |
| - | * Length: 9.5cm width: 7cm height: 3.5cm Length of line: 40cm | + | * Speed Range: 0% to 100%(variable) |
| - | * Control port : | + | * Regulation Method: Potentiometer(Linear) |
| - | * 5V: driver board internal 5V power supply, the output capacity of less than 100mA, with potentiometer mode is recommended only to use , do not drive other circuits | + | * Regulation Type: Regulating Current(cannot be used as a voltage regulator) |
| - | * PWM: external PWM control signal input level range ,3-20V , 2mA current requirements ; | + | * Control Frequency: 15KHz(pulse width) |
| - | * ADJ: external 0-5V or 0-10V control signal input | + | * Wiring Type: Screw terminal |
| - | * GND: ground control signals , such as the shield shell is not allowed to pick pick here is also not allowed in this place other circuits connected GND, | + | * Rotary Knob: 100K with switch(270°) |
| - | * DOWN: control signal, the internal coupler control signal and GND effective turn ( optocoupler turns on, can also be used microcontroller , NPN switch | + | * Size: 75 x 56 x 28mm / 2.95 x 2.2 x 1.1" |
| - | * UP: control signal, the internal coupler control signal and GND effective turn ( optocoupler turns on, can also be used microcontroller , NPN switch control | + | |
| - | * STOP: control signal, the internal coupler control signal and GND effective turn ( optocoupler turns on, can also be used microcontroller , NPN switch control ) | + | |
documentation/electronique/modules_kits/controleurs_pwm/index.1582410169.txt.gz · Dernière modification : de f1sls
Outils de la page
Sauf mention contraire, le contenu de ce wiki est placé sous les termes de la licence suivante : CC Attribution-Share Alike 4.0 International
