Outils pour utilisateurs
TINYSA
Différences
Ci-dessous, les différences entre deux révisions de la page.
| Les deux révisions précédentesRévision précédenteProchaine révision | Révision précédente | ||
| documentation:mesure:tinysa:index [2022/08/29 12:35] – f1sls | documentation:mesure:tinysa:index [2022/08/29 12:47] (Version actuelle) – [SOFTWARE] f1sls | ||
|---|---|---|---|
| Ligne 6: | Ligne 6: | ||
| ===== SPECIFICATIONS ===== | ===== SPECIFICATIONS ===== | ||
| - | ==== USER INTERFACE ==== | + | ==== USER INTERFACE |
| * Display resolution 320*240 pixels | * Display resolution 320*240 pixels | ||
| Ligne 18: | Ligne 18: | ||
| - | ==== LOW INPUT MODE ==== | + | ==== LOW INPUT MODE SPECS ==== |
| * Input frequency range from 100kHz to 350MHz (with some limitations down to 10kHz) | * Input frequency range from 100kHz to 350MHz (with some limitations down to 10kHz) | ||
| Ligne 42: | Ligne 42: | ||
| * After a small HW modification it is possible to Listen to the demodulated audio | * After a small HW modification it is possible to Listen to the demodulated audio | ||
| - | ==== HIGH INPUT MODE ==== | + | ==== HIGH INPUT MODE SPECS ==== |
| - | | + | * Input frequency range from 240MHz to 960MHz |
| - | Input impedance is frequency dependent and deviates from 50 ohm | + | |
| - | As there is no input band filter, strong input signals outside the 240MHz to 960MHz range can cause distortion of the in band signals | + | |
| - | Absolute maximum input level without attenuation of +10dBm | + | |
| - | Input Intercept Point of third order modulation products (IIP3) of -5dBm with no internal attenuation | + | |
| - | 1dB compression point at -6dBm with no internal attenuation | + | |
| - | Power detector resolution of 0.5dB and linearity versus frequency of +/-2dB | + | |
| - | Absolute power level accuracy after power level calibration of +/- 2dB | + | |
| - | Lowest discernible signal using a resolution bandwidth of 30kHz of -115dBm | + | |
| - | Frequency accuracy equal to the selected resolution bandwidth | + | |
| - | Spur free dynamic range when using a 30kHz resolution bandwidth of 50dB | + | |
| - | Manually selectable resolution filters of 3, 10, 30, 100, 300, 600kHz. Automatic selection of one of the 57 resolution filters. | + | |
| - | Optional 25dB to 40dB frequency dependent input attenuator. The power level error with this attenuator activated increases to +/- 10dB | + | |
| - | On screen resolution of 51, 101, 145 or 290 measurement points. | + | |
| - | Scanning speed of over 1000 points/ | + | |
| - | Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth | + | |
| - | After a small HW modification it is possible to Listen to the demodulated audio | + | |
| - | + | ||
| - | Low output mode spec: | + | |
| - | Sinus output with harmonics below -40dB of fundamental | + | ==== LOW OUTPUT MODE SPECS ==== |
| - | Output frequency range from 100kHz to 350MHz | + | |
| - | Level accuracy +/- 2dB over the whole output frequency range | + | |
| - | Output frequency resolution either 156Hz below 47MHz output or 312Hz above 47MHz output | + | |
| - | Output level selectable in 1dB steps between -76dBm and -6dBm | + | |
| - | Optional AM, narrow FM and wide FM modulation with frequencies between 50Hz and 6kHz or slow sweep over selectable frequency span | + | |
| - | Optional output level sweep over maximum the entire output level range | + | |
| - | High output | + | * Sinus output |
| + | * Output frequency range from 100kHz to 350MHz | ||
| + | * Level accuracy +/- 2dB over the whole output frequency range | ||
| + | * Output frequency resolution either 156Hz below 47MHz output or 312Hz above 47MHz output | ||
| + | * Output level selectable in 1dB steps between -76dBm and -6dBm | ||
| + | * Optional AM, narrow FM and wide FM modulation with frequencies between 50Hz and 6kHz or slow sweep over selectable frequency span | ||
| + | * Optional output level sweep over maximum the entire output level range | ||
| - | Square wave output | + | ==== HIGHT OUTPUT MODE SPECS ==== |
| - | Output frequency range from 240MHz to 960MHz | + | |
| - | Output frequency resolution either 156Hz below 480MHz output or 312Hz above 480MHz output | + | |
| - | Output level selectable in variable increments between -38dBm and +9dBm | + | |
| - | Optional narrow FM and wide FM modulation with frequencies between 50Hz and 6kHz or slow sweep over selectable frequency span | + | |
| - | Reference generator spec: | + | * Square wave output |
| + | * Output frequency range from 240MHz to 960MHz | ||
| + | * Output frequency resolution either 156Hz below 480MHz output or 312Hz above 480MHz output | ||
| + | * Output level selectable in variable increments between -38dBm and +9dBm | ||
| + | * Optional narrow FM and wide FM modulation with frequencies between 50Hz and 6kHz or slow sweep over selectable frequency span | ||
| - | Optional square wave output with fundamental at -26dBm connected to high input/ | + | ==== REFERENCE GENERATOR SPECS ==== |
| - | Frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz. | + | |
| - | Battery spec: | + | * Optional square wave output with fundamental at -26dBm connected to high input/ |
| + | * Frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz. | ||
| + | |||
| + | ==== BATTERY SPECS ==== | ||
| - | | + | * Charging time max 1 hour on 500mA minimum USB port or USB charger |
| - | Operation on fully charged battery for at least 2 hours | + | |
| Ligne 96: | Ligne 96: | ||
| ===== SOFTWARE ===== | ===== SOFTWARE ===== | ||
| + | * TinySA-saver : https:// | ||
documentation/mesure/tinysa/index.1661769309.txt.gz · Dernière modification : de f1sls
Outils de la page
Sauf mention contraire, le contenu de ce wiki est placé sous les termes de la licence suivante : CC Attribution-Share Alike 4.0 International
