Différences

Ci-dessous, les différences entre deux révisions de la page.

--- documentation:mesure:tinysa:index [2022/08/29 12:44] – f1sls
+++ documentation:mesure:tinysa:index [2022/08/29 12:47] (Version actuelle) – [SOFTWARE] f1sls
@@ Ligne 44: / Ligne 44: @@
 ==== HIGH INPUT MODE SPECS ====
-    Input frequency range from 240MHz to 960MHz
+  * Input frequency range from 240MHz to 960MHz
-    Input impedance is frequency dependent and deviates from 50 ohm
+  * Input impedance is frequency dependent and deviates from 50 ohm
-    As there is no input band filter, strong input signals outside the 240MHz to 960MHz range can cause distortion of the in band signals
+  * As there is no input band filter, strong input signals outside the 240MHz to 960MHz range can cause distortion of the in band signals
-    Absolute maximum input level without attenuation of +10dBm
+  * Absolute maximum input level without attenuation of +10dBm
-    Input Intercept Point of third order modulation products (IIP3) of -5dBm with no internal attenuation
+  * Input Intercept Point of third order modulation products (IIP3) of -5dBm with no internal attenuation
-dB compression point at -6dBm with no internal attenuation
+  * 1dB compression point at -6dBm with no internal attenuation
-    Power detector resolution of 0.5dB and linearity versus frequency of +/-2dB
+  * Power detector resolution of 0.5dB and linearity versus frequency of +/-2dB
-    Absolute power level accuracy after power level calibration of +/- 2dB
+  * Absolute power level accuracy after power level calibration of +/- 2dB
-    Lowest discernible signal using a resolution bandwidth of 30kHz of -115dBm
+  * Lowest discernible signal using a resolution bandwidth of 30kHz of -115dBm
-    Frequency accuracy equal to the selected resolution bandwidth
+  * Frequency accuracy equal to the selected resolution bandwidth
-    Spur free dynamic range when using a 30kHz resolution bandwidth of 50dB
+  * Spur free dynamic range when using a 30kHz resolution bandwidth of 50dB
-    Manually selectable resolution filters of 3, 10, 30, 100, 300, 600kHz. Automatic selection of one of the 57 resolution filters.
+  * Manually selectable resolution filters of 3, 10, 30, 100, 300, 600kHz. Automatic selection of one of the 57 resolution filters.
-    Optional 25dB to 40dB frequency dependent input attenuator. The power level error with this attenuator activated increases to +/- 10dB
+  * Optional 25dB to 40dB frequency dependent input attenuator. The power level error with this attenuator activated increases to +/- 10dB
-    On screen resolution of 51, 101, 145 or 290 measurement points.
+  * On screen resolution of 51, 101, 145 or 290 measurement points.
-    Scanning speed of over 1000 points/second using largest resolution filters.
+  * Scanning speed of over 1000 points/second using largest resolution filters.
-    Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth
+  * Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth
-    After a small HW modification it is possible to Listen to the demodulated audio
+  * After a small HW modification it is possible to Listen to the demodulated audio
 ==== LOW OUTPUT MODE SPECS ====
@@ Ligne 96: / Ligne 96: @@
 ===== SOFTWARE =====
+  * TinySA-saver : https://github.com/erikkaashoek/tinySA-saver

Outils pour utilisateurs

Outils du site

Différences

Outils de la page